Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
Presented here down the page you will find lots of helpful ideas on the subject of Tools You Need to Install a New Bathtub .
Installing a bathtub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately tough task. If the old tub is readily accessible, the project can move rapidly; if you have to open a wall to remove the old bathtub and position the new bathtub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the work and are comfortable attempting it. As opposed to working with a specialist to take control of a halfway-completed task, it is far better to think about utilizing one before you begin. Chances are you may require a professional plumber to make tube links.
This write-up will help you install a brand-new bath tub in your washroom if you have actually currently bought a new bathtub and do not require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist should consist of the following:
Preparing for the Installment
Firstly, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop stress on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited accessibility that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before moving on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are useful in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the tub up until the level reviews level.
To install faucets, fit the bottom of the furthest flexible tap port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water and also examine all joints as well as brand-new pipework for leaks and also tighten them if necessary. Load the tub as well as also check the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making certain that the washing machines remain in place in between the faucet and the sink. Protect the faucet in place with the producer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, creating the water to permeate the wall between the bathroom and the tiling, causing complications with wetness as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and cartridges, as well as are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill the bathtub with water prior to sealing, to permit the activity experienced when the bathtub is in use. The sealant can break relatively very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that review on How to Install a Bathtub while doing a lookup on the search engines. Enjoyed reading our blog? Please share it. Help another person check it out. Thanks for your time. Don't hesitate to visit our site back soon.
Book A Free Estimate Report this page